There are many versions of this module. TEA5767 FM Stereo Audio Radio Module for Arduino 76-108MHZ With Cable Antenna.
The module uses the TEA5767 radio chip, this one here. The signal level will only be update on - If you get some glitches on the encoder or on the pushbutton, use a snubber network, like this:Arduino pin >----+----/\/\/\/---------> Encoder or switch pin// Get TEA5767 library at https://github.com/andykarpov/TEA5767// LCD column pixel index (0 <= lcdBase <= (16 * 5))// LCD pixel column index within the character (0 <= lcdMinor <= 4)// The radio dial needle is not at the leftmost position:// clean the character on the left (to erase previous neddle position)// Not at rightmost position: clear the character on the right// Create custom character to represent all (5) possible needle?s position// Japanese character that looks like an antenna :)// Automatic search mode (only processed if the radio is not currently performing a search)// Automatic search mode (only processed if the radio is not currently performing a search) About: Arduino Tutorials by Codebender.cc Team Dazu nehmen wir eine Lochrasterplatine, die wir mit einem Dremel und einer Trennscheibe (oder einer Säge) zurechtschneiden:Danach bearbeiten wir zwei 5 polige Stiftleisten bei denen wir die Stifte soweit reindrücken, dass diese etwa 1mm oben überstehen und verzinnen selbige mit Lötzinn um das spätere Auflöten des Chips zu vereinfachen (die mir vorliegenden waren zum Glück schon verzinnt):Nun stecken wir die Stiftleisten auf die fertige Lochrasterplatine und löten sie fest:Anschließend nehmen wir uns etwas Schaltdraht, entfernen die Isolierung und schneiden uns 10 etwa 1cm lange Stückchen zurecht.
nehmen.
The RDA5807M — a single-chip broadcast FM stereo radio tuner with fully integrated synthesizer, IF selectivity, RDS/RBDS and MPX decoder — supports frequency range from 50 MHz to 115 MHz.
Essentially, the Arduino sends the radio chip commands over the I2C bus and the radio chip subsequently replies to the commands by performing the requested action and returning status information.
/* Simple radio tuner using Arduino Leonardo and the Philips TEA5767 module (Arduino Uno version) Notes:----- The TEA5767 maximum supply voltage is 5V.
Thank you very much! But My question is does the TEA5767 can act as transmitter. Ximimark 1Pcs TEA5767 Radio Module FM Stereo Radio Module for Arduino 76-108MHZ Frequency AGC Circuit with Free Cable Antenna. Reply
You may built FM or Radio receivers by using radio tuner components and it requires lot of efforts to built accurate radio receiver. On the module, we can also find an audio amplifier. FM-Stereo-Radio TEA5767-Modul und ein Arduino.
But there is not any sound. 4.6 out of 5 stars 8.
We can further reduce the current some software and hardware tricks so this project can be battery powered.
I am transmitting some YouTube safe tracks using this inexpensive FM transmitter at this frequency. Very nice project sir! How to Use the TEA5767 FM Radio Module - Arduino Tutorial: In this tutorial you will learn how to use the TEA5767 FM radio module with Arduino uno board. Step 2: Preparing the FM Radio Module Audio outputs of the TEA5767, via a stereo potentiometer, are connected to the D class power amplifier module with the power of 2x3w which is quite enough for this purpose. Of course it does not works with the TEAD5767Radio library. I modified his code by adding two analog meters for reading the signal strength and frequency, "stereo" LED, and "auto /manual search" LED.
There will be more of them, so make sure to click Follow button!I made it.Frequency,Signal level .. are viewed in Serial monitor as above picture.
Answer
Wireless Connection Between Micro Controllers Using nRF24L01.
(Eventuell noch einmal nachlöten.)
DIY Si4730 All Band Radio (LW, MW, SW, FM) Project tutorial by Mirko Pavleski.
3 years ago
I want to turn this project into complete radio with a retro 3D printed enclosure. 2 years ago
The chip uses the I2C interface, so it is straightforward to use with Arduino. These modules use I2C and are available on eBay for just a few dollars each. Roll and then move along the board, gaining points from mini games by using a phone.Simple radio tuner using Arduino Leonardo and the Philips TEA5767 module (Arduino Uno version)- The TEA5767 maximum supply voltage is 5V. Check it out.
So, I connect only two of the wires. Be sure your Arduino is not sourcing more than 5V - The TEA5767 does not update the signal level indicator on read.
Be sure your Arduino is not sourcing more than 5V- The TEA5767 does not update the signal level indicator on read.
Reply Do you find this project interesting?
This is a mini stereo FM radio module equipped with TEA5767 chip supporting 76-108MHz automatically digital turning, high stability,low noise. Um auch beim Basteln nebenbei noch ein wenig unterhalten zu werden, bauen wir uns heute ein kleines FM-Stereo-Radio – auch als Als erstes bauen wir uns einen Adapter für den TEA5767.
You can make your own digital fm radio for your desk with LCD display and speakers, check this project I hope you liked this, let me know in the comments. Do you have any tricks from your experience that can improve this project?Please post your comments in the comments section below and don’t forget to like the video and share it with your friends if you find it interesting! 1m langer Draht verwendet werden, bei mir ging es auch ohne und war sogar besser, da die Antenne merkwürdigerweise Störgeräusche fabriziert hat.Für das Display müssen noch 2 zusätzliche Bibliotheken installiert werden:Nun noch den Sketch auf den Arduino laden und schon kann es losgehen:Die Mono/Stereo-Anzeige erfolgt automatisch, ist aber leider bei „Ton aus“ immer Mono.
6 months ago